Cisco 2600 ios image file

Proposed idle-PC value: The c supports up to 2 Network Modules maximum of 8 Ethernet ports, 32 FastEthernet ports or 8 serial ports.

Release Notes for Cisco 2600 Series for Cisco IOS Release 12.2 XT

The c supports up to 4 Network Modules maximum of 16 Ethernet ports, 32 FastEthernet ports or 16 serial ports. Only the is supported, it has 6 Port Adapters PA slots. This router series is still getting new IOS The last one at this date is: This one is not the latest At this moment, it is not possible to emulate Catalyst switches with Dynamip. This is due to the impossibility to emulate ASIC processors used in those type of devices.

How to install

However , if you want to use Dynamips you can use the EtherSwitch module with s, s and s Series. Keep in mind that this module works differently uses the vlan database etc. To recap: Download a TFTP server.

HD - Cisco IOS Image Backup and Restore/Upgrade via TFTP

Specify the outbound file directory. This is the directory in which the Cisco IOS software images are stored. Most TFTP applications provide a setup routine in order to assist in these configuration tasks.


  1. Other versions.
  2. game cheat codes for java phones.
  3. Access Routers Software Upgrade Procedures.
  4. download wifi hacker for blackberry 8520.

Even if it is possible to connect to the router through a Telnet session, Cisco recommends that you connect directly to the router through the console port because, if something goes wrong during the upgrade, you might need to be physically present next to the router to power-cycle it. Moreover, the Telnet connection is lost while the router reboots during the upgrade procedure.

Cisco IOS Cookbook, 2nd Edition by Ian Brown, Kevin Dooley

A rolled cable, usually a flat black cable, connects the console port of the router to one of the COM ports of the PC. If garbage characters appear in the HyperTerminal session, either you have not set the HyperTerminal properties properly or the config-register of the router is set to a non-standard value for which the console connection speed is higher than bps. In order to check the value of the config-register, issue the show version command.

The config-register values appears in the last line of the output. Verify that this value is set to 0x or 0x In order for a configuration register change to take effect, you must reload the router. When you are sure that the console speed is set to bps on the router side, you should check the HyperTerminal properties. When you are connected to the console port of the router, you might notice that the router is either in ROMmon or Boot mode. These two modes are used for recovery and diagnostic procedures.

If you do not see the usual router prompt, you should use these recommendations in order to proceed with the upgrade procedure installation:.

The router boots in ROMmon mode, and this message appears when you issue the dir flash: This error message displays when the Flash is empty or the filesystem is corrupted. You might also need to consult the Boot Failure procedures specific to your platform.

Naming Convention of Cisco IOS Image Files

Choose your platform from the Product Support Selector in order to locate these procedures. Look in the Troubleshooting section of each document. These error messages display in the console output when the Flash is empty or when the file system is corrupted. Copy a valid image on the Flash as described in the procedures provided in this document.

Your first step in the upgrade procedure is to select the correct Cisco IOS software release and feature set. This step is very important, and these factors can affect the decision for which Cisco IOS you should select:. Memory requirement: This ensures that the IOS image was not corrupted during transmission. If the image does not pass the verification test, attempt your download again and do not reload the router.

Table Of Contents

You can manually check to see if the IOS checksum is correct by using the verify command. We show how to use the verify command in Recipe 1.

Cisco Series - Cisco IOS Release (2)XT - Cisco

If the IOS upgrade goes smoothly and the checksum verifies correctly, then it is safe to reboot your router to load the new IOS image. Once the router becomes reachable again, you should verify the new IOS loaded correctly with the show version command:. This indicates the IOS upgrade was completely successful. Stay ahead with the world's most comprehensive technology and business learning platform.

With Safari, you learn the way you learn best. Get unlimited access to videos, live online training, learning paths, books, tutorials, and more.